|
| enum | CO_errorRegister_t {
CO_ERR_REG_GENERIC_ERR = 0x01U,
CO_ERR_REG_CURRENT = 0x02U,
CO_ERR_REG_VOLTAGE = 0x04U,
CO_ERR_REG_TEMPERATURE = 0x08U,
CO_ERR_REG_COMMUNICATION = 0x10U,
CO_ERR_REG_DEV_PROFILE = 0x20U,
CO_ERR_REG_RESERVED = 0x40U,
CO_ERR_REG_MANUFACTURER = 0x80U
} |
| | CANopen Error register. More...
|
| |
| enum | CO_EM_errorCode_t {
CO_EMC_NO_ERROR = 0x0000U,
CO_EMC_GENERIC = 0x1000U,
CO_EMC_CURRENT = 0x2000U,
CO_EMC_CURRENT_INPUT = 0x2100U,
CO_EMC_CURRENT_INSIDE = 0x2200U,
CO_EMC_CURRENT_OUTPUT = 0x2300U,
CO_EMC_VOLTAGE = 0x3000U,
CO_EMC_VOLTAGE_MAINS = 0x3100U,
CO_EMC_VOLTAGE_INSIDE = 0x3200U,
CO_EMC_VOLTAGE_OUTPUT = 0x3300U,
CO_EMC_TEMPERATURE = 0x4000U,
CO_EMC_TEMP_AMBIENT = 0x4100U,
CO_EMC_TEMP_DEVICE = 0x4200U,
CO_EMC_HARDWARE = 0x5000U,
CO_EMC_SOFTWARE_DEVICE = 0x6000U,
CO_EMC_SOFTWARE_INTERNAL = 0x6100U,
CO_EMC_SOFTWARE_USER = 0x6200U,
CO_EMC_DATA_SET = 0x6300U,
CO_EMC_ADDITIONAL_MODUL = 0x7000U,
CO_EMC_MONITORING = 0x8000U,
CO_EMC_COMMUNICATION = 0x8100U,
CO_EMC_CAN_OVERRUN = 0x8110U,
CO_EMC_CAN_PASSIVE = 0x8120U,
CO_EMC_HEARTBEAT = 0x8130U,
CO_EMC_BUS_OFF_RECOVERED = 0x8140U,
CO_EMC_CAN_ID_COLLISION = 0x8150U,
CO_EMC_PROTOCOL_ERROR = 0x8200U,
CO_EMC_PDO_LENGTH = 0x8210U,
CO_EMC_PDO_LENGTH_EXC = 0x8220U,
CO_EMC_DAM_MPDO = 0x8230U,
CO_EMC_SYNC_DATA_LENGTH = 0x8240U,
CO_EMC_RPDO_TIMEOUT = 0x8250U,
CO_EMC_TIME_DATA_LENGTH = 0x8260U,
CO_EMC_EXTERNAL_ERROR = 0x9000U,
CO_EMC_ADDITIONAL_FUNC = 0xF000U,
CO_EMC_DEVICE_SPECIFIC = 0xFF00U,
CO_EMC401_OUT_CUR_HI = 0x2310U,
CO_EMC401_OUT_SHORTED = 0x2320U,
CO_EMC401_OUT_LOAD_DUMP = 0x2330U,
CO_EMC401_IN_VOLT_HI = 0x3110U,
CO_EMC401_IN_VOLT_LOW = 0x3120U,
CO_EMC401_INTERN_VOLT_HI = 0x3210U,
CO_EMC401_INTERN_VOLT_LO = 0x3220U,
CO_EMC401_OUT_VOLT_HIGH = 0x3310U,
CO_EMC401_OUT_VOLT_LOW = 0x3320U
} |
| | CANopen Error code. More...
|
| |
| enum | CO_EM_errorStatusBits_t {
CO_EM_NO_ERROR = 0x00U,
CO_EM_CAN_BUS_WARNING = 0x01U,
CO_EM_RXMSG_WRONG_LENGTH = 0x02U,
CO_EM_RXMSG_OVERFLOW = 0x03U,
CO_EM_RPDO_WRONG_LENGTH = 0x04U,
CO_EM_RPDO_OVERFLOW = 0x05U,
CO_EM_CAN_RX_BUS_PASSIVE = 0x06U,
CO_EM_CAN_TX_BUS_PASSIVE = 0x07U,
CO_EM_NMT_WRONG_COMMAND = 0x08U,
CO_EM_TIME_TIMEOUT = 0x09U,
CO_EM_TIME_LENGTH = 0x0AU,
CO_EM_0B_unused = 0x0BU,
CO_EM_0C_unused = 0x0CU,
CO_EM_0D_unused = 0x0DU,
CO_EM_0E_unused = 0x0EU,
CO_EM_0F_unused = 0x0FU,
CO_EM_10_unused = 0x10U,
CO_EM_11_unused = 0x11U,
CO_EM_CAN_TX_BUS_OFF = 0x12U,
CO_EM_CAN_RXB_OVERFLOW = 0x13U,
CO_EM_CAN_TX_OVERFLOW = 0x14U,
CO_EM_TPDO_OUTSIDE_WINDOW = 0x15U,
CO_EM_16_unused = 0x16U,
CO_EM_17_unused = 0x17U,
CO_EM_SYNC_TIME_OUT = 0x18U,
CO_EM_SYNC_LENGTH = 0x19U,
CO_EM_PDO_WRONG_MAPPING = 0x1AU,
CO_EM_HEARTBEAT_CONSUMER = 0x1BU,
CO_EM_HB_CONSUMER_REMOTE_RESET = 0x1CU,
CO_EM_1D_unused = 0x1DU,
CO_EM_1E_unused = 0x1EU,
CO_EM_1F_unused = 0x1FU,
CO_EM_EMERGENCY_BUFFER_FULL = 0x20U,
CO_EM_21_unused = 0x21U,
CO_EM_MICROCONTROLLER_RESET = 0x22U,
CO_EM_23_unused = 0x23U,
CO_EM_24_unused = 0x24U,
CO_EM_25_unused = 0x25U,
CO_EM_26_unused = 0x26U,
CO_EM_27_unused = 0x27U,
CO_EM_WRONG_ERROR_REPORT = 0x28U,
CO_EM_ISR_TIMER_OVERFLOW = 0x29U,
CO_EM_MEMORY_ALLOCATION_ERROR = 0x2AU,
CO_EM_GENERIC_ERROR = 0x2BU,
CO_EM_GENERIC_SOFTWARE_ERROR = 0x2CU,
CO_EM_INCONSISTENT_OBJECT_DICT = 0x2DU,
CO_EM_CALCULATION_OF_PARAMETERS = 0x2EU,
CO_EM_NON_VOLATILE_MEMORY = 0x2FU,
CO_EM_MANUFACTURER_START = 0x30U,
CO_EM_MANUFACTURER_END = CO_CONFIG_EM_ERR_STATUS_BITS_COUNT - 1
} |
| | Error status bits. More...
|
| |
|
| CO_ReturnError_t | CO_EM_init (CO_EM_t *em, const OD_entry_t *OD_1001_errReg, const OD_entry_t *OD_1014_cobIdEm, CO_CANmodule_t *CANdevTx, uint16_t CANdevTxIdx, const OD_entry_t *OD_1015_InhTime, const OD_entry_t *OD_1003_preDefErr, const OD_entry_t *OD_statusBits, CO_CANmodule_t *CANdevRx, uint16_t CANdevRxIdx, const uint8_t nodeId) |
| | Initialize Emergency object. More...
|
| |
| void | CO_EM_initCallbackPre (CO_EM_t *em, void *object, void(*pFunctSignal)(void *object)) |
| | Initialize Emergency callback function. More...
|
| |
| void | CO_EM_initCallbackRx (CO_EM_t *em, void(*pFunctSignalRx)(const uint16_t ident, const uint16_t errorCode, const uint8_t errorRegister, const uint8_t errorBit, const uint32_t infoCode)) |
| | Initialize Emergency received callback function. More...
|
| |
| void | CO_EM_process (CO_EM_t *em, bool_t NMTisPreOrOperational, uint32_t timeDifference_us, uint32_t *timerNext_us) |
| | Process Error control and Emergency object. More...
|
| |
| void | CO_error (CO_EM_t *em, bool_t setError, const uint8_t errorBit, uint16_t errorCode, uint32_t infoCode) |
| | Set or reset error condition. More...
|
| |
| static bool_t | CO_isError (CO_EM_t *em, const uint8_t errorBit) |
| | Check specific error condition. More...
|
| |
| static uint8_t | CO_getErrorRegister (CO_EM_t *em) |
| | Get error register. More...
|
| |
CANopen Emergency protocol.
- Author
- Janez Paternoster
- Copyright
- 2020 Janez Paternoster
This file is part of CANopenNode, an opensource CANopen Stack. Project home page is https://github.com/CANopenNode/CANopenNode. For more information on CANopen see http://www.can-cia.org/.
Licensed under the Apache License, Version 2.0 (the "License"); you may not use this file except in compliance with the License. You may obtain a copy of the License at
http://www.apache.org/licenses/LICENSE-2.0
Unless required by applicable law or agreed to in writing, software distributed under the License is distributed on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the License for the specific language governing permissions and limitations under the License.
1.8.17